Automobile Engine Speed Sensor Transducer Transmitter Gvs-H-03 Vehicle ABS System

GVS-001 Hall-Effect Gear Speed SensorDescription GVS Series Tooth Sensors use a magnetically biased Hall effect integrated circuit to accurately sense movement of ferrous metal targets. This specially designed I.C., with discrete capacitor and bias magnet, is sealed in a probe type package for physical protection and cost effective installation. Output is digital, current sinking (open Collector). Reverse polarity protection is standard. If power is inadvertently wired backwards, the sensor will not be damaged. Optimum sensor performance is dependent on the following variables which must be considered in combination: Target material, geometry, and speed Sensor/target gap Ambient temperature Magnetic material in close proximity Features Senses ferrous metal targets Digital current sinking output (open collector) Better signal-to-noise ratio than variable reluctance sensors, excellent low speed performance, output amplitude not dependent on RPM Sensor electronically self-adjusts to slight variations in runout and variations in temperature, simplifying installation and maintenance Fast operating speed - over 100 kHz EMI resistant Reverse polarity protection and transient protection (integrated into Hall I.C.) Wide continuous operating temperature range Typical Applications Automotive and Heavy Duty Vehicles:Camshaft and crankshaft speed/position Transmission speed Tachometers Anti-skid/traction control, ABS system Industrial: Sprocket speed Chain link conveyor speed and distance Stop motion detector High speed low cost proximity Tachometers, Counters Gear tooth Sensor Specifications All values were measured using 1 K pull-up resistor. Electrical Supply Voltage 4.5 to 24 VDC Output Voltage (output low) 0.4 V max. Output Current (output high) 10 µA max. leakage into sensor Switching Time Rise (10 to 90%) 15 µsec. max.Fall (90 to 10%) 1.0 µsec. max. Absolute Supply Voltage (Vs) ±30 VDC continuous Maximum Voltage Externally Applied Ratings To Output (output high) -0.5 to +30 V Output Current 40 mA sinking Temperature RangeStorage -40 to 150°C (-40 to 302°F)Operating -40 to 150° C (-40to302°F) Switching Operate Point 3.7±1.25° (3,28±1,13 mm)Characteristics Release Point 4.7±2.50° (4,16±2,21 mm)Differential Travel 8.4±3.70° (7,45±3,34 mm) Target refrence and conditions The Target Guidelines table provides basic parameters when an application is not restricted to a specific target. Any target wheel that exceeds the follow-ing minimum specifications can be sensed over the entire temperature range of -40° to 150°C with any sensing gap up to 2,0mm. This data is based on a 102 mm diameter wheel, rotating 10 to 3600 RPM.Reference Target Dimensions Tooth Height: .200 in. (5,06 mm) min. Tooth Width: .100 in. (2,54 mm) min. Tooth Spacing: .400 in. (10,16 mm) min. Target Thickness: .250 in. (6,35 mm) Characteristics will vary due to target size, geometry, location, and material. Sensor specifications were derived using a cold-rolled steel reference target. See table, for reference target configuration and evaluation conditions. Target Diameter: 4 inch. (101,6 mm) Tooth Width: .350 inch. (8,89 mm)Thickness: .250 inch. (6,35 mm) Test Conditions Air Gap: .040 to .080 inch. (1,02 to 2,03 mm)Power Supply: 4.5 to 24 VdcRPM: 10 min., 3600 max.Mounting dimension (For reference only) Photos/* January 22, 2024 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1